sea.bin images provided by Apple now is to use old versions of StuffIt Expander, which I have not attempted due to time constraints. sea.bin, making it harder to install them using Mini vMac. So I guess it was only recently that the disk images provided by the download page were changed to. When I first attempted to install System 7.5.5 and wrote this article, I did not have major issues mounting the installer disk images. While I do not have the time to verify this information, I do recall that Apple’s old software download page has changed over the years. sea.bin images using DiskCopy 4.2, which apparently requires an actual floppy disk drive. smi.bin format and the instructions provided in the download ask him to extract. sea.bin format, there is no way to convert them into a format readable by Mini vMac, as HFVExplorer only supports. In particular, one reader commented that since the upgrade disk images for System 7.5.5 downloaded from Apple are in. This section was added in August 2014 after I received comments from several readers asking for detailed instructions to upgrade to System 7.5.5 from System 7.5.3 using the disk images provided by Apple. Method 1: Installing System 7.5.5 from pre-made disk images Once your installation is completed, refer to my latest article for a list of interesting old Mac applications which you can play with using Mini vMac, Basilisk and SheepShaver. For a video tutorial, watch this Youtube clip (credits to Peak66 for creating this tutorial). Also try out PCE/macplus, a newer and more advanced 68k Macintosh emulator.īefore you start, download Mini vmac and find an appropriate ROM such as this one. Source: RetroMacCast Image: All photos by John Leake, used with permission.This guide shows you how to install System 7.5.5 for the Mini vMac emulator. When can we order one? Leake with his newly birthed creation. More info is available in the latest RetroMacCast, which is rapidly approaching its 300th episode! Nice work, John. “It’s not as bad as I thought,” he says, “especially since to get Mini vMac to run at full screen I had to adjust the boot config file to get it to output at 512×384, which is then being shoved onto a screen with a resolution of 320×200.”Īnother video gives more details of the design and shows the Mini Mac in action (there’s no sound, apparently the audio output of Mini vMac on the Raspberry Pi is a bit glitchy): Leake was worried the tiny screen would be completely unreadable, but things turned out OK. On top of this is the Mini vMac emulator running System Software 6.0.8. On the software side, the Raspberry Pi is running Rasbian, a modified version on Debian Linux. Back in 2010 he converted a Mac Plus into the infamous Banana Junior from the comic strip Bloom County. This may be the only Compact Macintosh in the world with an HDMI output port!Ĭustom creations are nothing new to this Mac über-fan. The last thing I had to do was to solder wires directly to the Pi board to bypass the power connector.” The rear case sports two USB ports, an HDMI port, and an ethernet jack. I also had to cut away quite a bit of the USB cable on the top to get it to bend below the top of my case. “On the Pi, I had to cut the SD card down almost flush with the edge of the Raspberry Pi board. To make everything fit, Leake had to make a few modifications. On top is a two-port USB charger that powers the Raspberry Pi and the monitor. One of the inside ports holds a Wi-Fi dongle, the other a Bluetooth dongle. The cramped innards contain a Raspberry Pi (left), a few USB hubs and power supplies. Two USB ports are facing out and two facing in. The Raspberry Pi (aka “the motherboard”) sits on the left next to a four-port powered USB hub. The monitor is a 3.5-inch composite LCD panel, held in place with two brackets and a few Velcro tabs. Mini Macintosh next to the full-size model. If he decides to make more of these super-cute miniscule Macs, he may employ a 3D printer rather than manually crafting elements. The sides, bottom and front were glued together to make one piece and the top and back a second piece.ĭuring the podcast discussing Mini Mac, Leake notes that the assembly took about twelve hours total. He then used files and sandpaper to shape the bezels, with extra care taken around the curves near the screen. Leake made the case using sheets of PVC plastic ( white 3M Sintra) which yields easily to an X-Acto knife.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |